OLI-NATURA Scandic Oil - FurnitureParquet oil in raw wood effectOLI-NATURA Scandic Oil - Classic is inspired by Scandinavian style and combines a natural look with surface protection. It makes light wood look as if untreated and freshly sanded. The natural colour of the wood is almost unfired (highlighted). Only during processing does a colour deepening appear in the wet phase. This, however, disappears in the course of drying.This oil gets its raw wood effect from a VOC-free compound of vegetable oils, which we emulsify in water. Added to this is a fine pinch of light-stable white pigments, which round off the raw wood effect and provide UV protection. Due to its low viscosity, Scandic-Oil Classic is recommended for roller application on light wood floors such as oak, fir, spruce or ash. The dried coating is harmless to humans, animals and plants, complies with DIN EN 71-3 ( Safety of toys) as well as DIN 53160 ( Saliva and perspiration resistant) and is a building product approved by the German Institute for Building Technology (DIBt). Thanks to the intelligent formulation, the oil-soaked rags, pads or brushes do not tend to self-ignite . The applicationPreparation:Sand the wood surface carefully. Start with coarse sanding. Final sanding for furniture surfaces with P240 grit. Wood moisture content: 8-12%. The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature. Application: For the first oil application, apply oil evenly and generously with a short-pile microfibre roller. Work quickly because of the rapid drying and avoid rolling into oil that has already dried. Allow the surface to dry for at least 2-3 hours. Then sand the dried oil application intermediately with grit P220-P280. A P220 sanding sponge is best for this - Dust the surface well. Apply the second oil coat evenly with a microfibre roller and allow to dry. During application, a colour deepening occurs in the wet phase, which disappears after complete drying. The surface is dry and brittle? The water resistance is weakening? - Now it's time for maintenance! The following applies to everyday cleaning: Regular dusting forms the basis. Regular damp care with wood soap ensures quick cleanliness and regreasing. Never use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. The wood can always be refreshed with OLI-Natura Wood Refresher. It renews the protective effect and provides a water-repellent surface without changing the colour tone of the wood. Worn areas on floors or stairs that have been treated with OLI-NATURA Scandic-Oil can be partially sanded and re-oiled without having to re-treat the entire surface.Consumption: With 2 applications and depending on the absorbency of the substrate, approx. 60-80g per m² this corresponds to 12-15 m² per litre. Drying: Depending on humidity and temperature, the surface is: dust-dry after 1 hour, carefully walkable after 2 hours. Protect from water during the first 3-5 days until complete curing.

OLI-NATURA Linseed Oil VarnishThe most natural and original way to protect your wood.Natural. Vegan. Food safe: Our organic OLI-NATURA Linseed Oil Varnish is for many the most original and beautiful way to naturally protect interior and exterior wood. It is produced in a gentle cooking process exclusively from pure cold-pressed linseed oil and 0.4 % dry substances. After curing, the coating forms a clear and water-repellent protective layer, which is called varnish.Linseed oil varnish is a natural product that hardens through with the help of the oxygen contained in the air. Depending on the air humidity and temperature, the paint takes three weeks to cure completely. The drying process can be recognised by the characteristic linseed oil smell. It is either "love at first smell" or you turn up your nose. But the smell is completely harmless and disappears when the oil has hardened.Even for the treatment of children's toys and surfaces that come into contact with food, Linseed Oil Varnish can be used without hesitation. Thus, it complies with the toy standard DIN EN 71-3 (safety of toys) and has been tested and certified by an independent German testing laboratory with "letter and seal" for "food safety".The applicationPreparation: The substrate must be finely sanded and clean and free of dust and grease. Shake/stir container well before use. Application: Apply oil evenly in a thin layer in grain direction with a brush, flat brush or cotton cloth. Avoid excess as far as possible or after 30 minutes exposure time with a lint-free cotton cloth or oil absorbent cloth. The surface should appear evenly matt. After sufficient drying of 16-24 hours, further coats can be applied if necessary.Drying: Depending on humidity and temperature, the oiled surface is dust-dry after 1-2 hours and can be recoated after 16-24 hours. Complete hardening is achieved after 21 days. Treat gently during this time. Note: Oil-soaked cloths/pads can self-ignite due to heat build-up! Therefore clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA Scandic Oil - ClassicParquet oil in raw wood effectOLI-NATURA Scandic Oil - Classic is inspired by Scandinavian style and combines a natural look with surface protection. It makes light wood look as if untreated and freshly sanded. The natural colour of the wood is almost unfired (highlighted). Only during processing does a colour deepening appear in the wet phase. This, however, disappears in the course of drying.This oil gets its raw wood effect from a VOC-free compound of vegetable oils, which we emulsify in water. Added to this is a fine pinch of light-stable white pigments, which round off the raw wood effect and provide UV protection. Due to its low viscosity, Scandic-Oil Classic is recommended for roller application on light wood floors such as oak, fir, spruce or ash. The dried coating is harmless to humans, animals and plants, complies with DIN EN 71-3 ( Safety of toys) as well as DIN 53160 ( Saliva and perspiration resistant) and is a building product approved by the German Institute for Building Technology (DIBt). Thanks to the intelligent formulation, the oil-soaked rags, pads or brushes do not tend to self-ignite . The applicationPreparation:Sand the wood surface carefully. Start with coarse sanding. Final sanding for furniture surfaces with P240 grit. Wood moisture content: 8-12%. The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature. Application: For the first oil application, apply oil evenly and generously with a short-pile microfibre roller. Work quickly because of the rapid drying and avoid rolling into oil that has already dried. Allow the surface to dry for at least 2-3 hours. Then sand the dried oil application intermediately with grit P220-P280. A P220 sanding sponge is best for this - Dust the surface well. Apply the second oil coat evenly with a microfibre roller and allow to dry. During application, a colour deepening occurs in the wet phase, which disappears after complete drying. The surface is dry and brittle? The water resistance is weakening? - Now it's time for maintenance! The following applies to everyday cleaning: Regular dusting forms the basis. Regular damp care with wood soap ensures quick cleanliness and regreasing. Never use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. The wood can always be refreshed with OLI-Natura Wood Refresher. It renews the protective effect and provides a water-repellent surface without changing the colour tone of the wood. Worn areas on floors or stairs that have been treated with OLI-NATURA Scandic-Oil can be partially sanded and re-oiled without having to re-treat the entire surface.Consumption: With 2 applications and depending on the absorbency of the substrate, approx. 60-80g per m² this corresponds to 12-15 m² per litre. Drying: Depending on humidity and temperature, the surface is: dust-dry after 1 hour, carefully walkable after 2 hours. Protect from water during the first 3-5 days until complete curing.

OLI-NATURA Hard Wax Oil - NaturalThe classic oil-wax combination.OLI-NATURA Hard Wax Oil is a classic hard wax oil with 60% solid content for treating wood indoors and combines the best properties of wax and oil. While the oil penetrates the wood and protects it from the inside, the wax forms a robust and water-repellent surface film. The wood remains open-pored, can continue to breathe and thus has a positive influence on the indoor climate. The natural colour and grain of the wood are discreetly emphasised and the surface feels pleasant. The "OLI-NATURA Hard Wax Oil" consists of modified vegetable oils, such as soybean oil, and waxes, such as refined carnauba wax, dearomatised hydrocarbon as well as lead- and cobalt-free drying agents. In doing so, we deliberately avoid the use of critical substances such as preservatives, formaldehydes, aromatics, biocides, cobalt salts and oximes.It is "Allergy Friendly Quality Tested" and has been awarded the ECARF seal. It is also LFGB certified (food safe) and complies with Regulation (EC) No. 1935/2004. The cured material is harmless to humans, animals and plants. It complies with DIN EN 71-3 (Safety of toys) as well as DIN 53160 (Saliva and perspiration fastness) and is a building product approved by the German Institute for Building Technology (DIBt).The applicationThe preparation: Sand the wood surface carefully, start with coarse sanding, final sanding for furniture P180-240, for floors P100-150. wood moisture: 8-12%. The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well. For floors: Apply oil evenly in a thin layer with a microfibre roller, oil brush or surface brush. Work in sections of between 5 and 15 m². Allow to work in for approx. 30-45 minutes. Now massage in with a white pad by hand or polishing machine and remove excess oil with a cotton cloth or oil absorbent cloth. The surface should now be dry to the touch. After 6-8 hours, apply a second coat without intermediate sanding.In furniture: Apply a thin layer of oil evenly in the direction of the grain with a brush or flat brush. Allow to soak in for approx. 10-30 minutes. Now remove excess oil with a cotton cloth or oil absorbent cloth. The surface should now be dry to the touch. For large surfaces, use a white pad if necessary. If necessary, a second coat can be applied after 6-8 hours without intermediate sanding.The surface is dry and brittle? The water resistance and colour depth is weakening? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1-2 applications I Depending on the absorbency of the wood 40-50 g/m² per application (20-25 m²/l).Drying: Depending on humidity/temperature, the surface is dust-dry after 1-2 hours, fully hardened after 2-3 days. Protect from water during this time.Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA OLI-AQUA NORDIC raw wood effect finishEnvironmentally friendly water-based paint based on bio-acrylateThe water-based bio-acrylic-based furniture and staircase paint creates dull matt surfaces with a raw wood effect. The original color tone of the background remains almost unchanged on light coniferous wood and oak. The matt lacquer surface of less than 5 gloss does not tend to gloss and presents itself as evenly dull matt from all viewing angles. OLI-AQUA NORDIC is very solid (>40%), can be easily brushed, rolled or sprayed and is very easy to sand. In the wet phase, a milky veil develops, which disappears completely in the course of drying and for one extraordinary raw wood effect. The environmentally friendly raw wood effect paint delays the natural yellowing process and is free of aromatics. It has a nice gradient and a good stand, which is more vertical, especially with spray painting parts is vital.The OLI-AQUA NORDIC conforms to the EU Decopaint guidelines and fulfils the fire protection class DIN EN 13501-1. The hardened material is harmless to humans, animals and plants. It corresponds to DIN EN 71-3 (Safety of children's toys) and DIN 53160 (saliva and sweat fastness). The applicationPreparation: Carefully sand the wood surface, start with coarse sanding, final sanding for furniture surfaces with 150/180 grit. Wood moisture: 8-12%. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust be. Process material at room temperature. Shake or stir the contents of the container well.Processing: Apply the varnish evenly and generously with a brush or flat brush in the direction of the grain. Leave the surface to dry for at least 90 minutes. Now apply the dried varnish in the direction of the grain with grit P220-P280 sanded. Dust the surface well. Then evenly and generously apply the second application of varnish with a brush or a flat brush.Consumption: 2 applications, 80-100 g/m² per application (10-12 m²/l). Drying: Depending on the humidity and temperature, the surface is: dust-dry after 45 minutes, sandable after 90 minutes and fully resilient after 5-8 days. During this time, treat gently and protect from water.

OLI-Aqua Hardener 13.5This hardener component can optionally be added immediately before processing the following water-based varnishes: OLI-Aqua Nordic 18.40, OLI-Aqua Modu (18.30, 18.32 and 18.35). After adding the hardener, the cross-linking reaction between the basecoat and the hardener starts immediately. During the reaction, the viscosity of the lacquers changes.Application / processing instructions. Optimum processing conditions at 20°C and 50% relative humidity. Do not process below +15 °C Stir the hardener thoroughly into the basecoat in the specified mixing ratio shortly before use. Let the mixture stand for 10 minutes before processing. Close the container well and use up as soon as possible. Mixed material residues must not be allowed to cure in closed containers. When using a cup gun, dilute with max. 5% water. The end of the pot life is not indicated by a change in viscosity. Do not pour back excess material. Mixing ratios:OLI-AQUA NORDIC 18.40 I 1K/2K alcohol topcoat 21:1 (5%) - Max. 3 hours drip time OLI-AQUA MODU 18.32 I 1pack/2pack stair varnish 10:1 (10%) - Max. 4 hours dripping time. OLI-AQUA MODU 18.35 I 1C/2C stain varnish 10:1 (10%) - Max. 4 hours

Super Pads for Random Orbital Sanders in WhiteFor applying, working in, & polishing oils & waxes on natural wood surfacesThe Super Pads 152 mm in white, beige, and green consist of a blend of polyester and/or nylon fibers, which are coated with a tough, highly elastic acrylic/latex binder and have been impregnated and coated with abrasive particles (aluminum oxide) impregnated and coated. The Super Pads are suitable for sanding discs with a diameter of 125 mm & 150 mm. The pads can be used on both sides with equal effectiveness! This means frequent replacement is not necessary.The colors of the pads indicate a specific hardness/coarseness and associated properties. Dimensions: Ø 152 mmContents: 5 pieces, packed by type in a cardboard box Colors - PropertiesSuperpad, White (Polishing & Massaging Pad) Properties: Soft, extra thick, and non-abrasive (free of abrasives) For polishing care oils For polishing out & removing excess oil after the application time For oiling & waxing natural softwood surfacesSuperpad, beige (massaging pad - hardwood) Properties: Medium-soft, extra thick, and non-abrasive For oiling & waxing natural hardwood surfaces Even distribution and deep massage of the oil and waxSuperpad, green (cleaning pad) Properties: Hard, slightly abrasive For cleaning light to moderate soiling Raised wood fibers are cut down, smoothing the surface

OLI-NATURA Worktop OilSolvent-free worktop oil for particularly stressed solid wood surfacesThe OLI-NATURA Worktop-Oil combines linseed and tung oil in a perfect ratio. It is particularly recommended for the basic treatment & care of heavily used solid wood surfaces with frequent water contact such as in the kitchen & bathroom (kitchen worktops, Furniture & dining tables, washbasins in wet areas). The LFGB certification enables it to be used in food areas (restaurants, hotels, canteens, kindergartens, schools) without hesitation. Thanks to its high tung oil content, it is strongly water-repellent, which makes the surface extremely resistant. In addition, the wood remains open to diffusion, can breathe and absorb part of the humidity in the room. The oiled-impregnated surface is pleasantly lively and the color is deepened. In addition, the worktop oil dries matt and does not tend to shine, which underlines the high quality of the natural oil surface.The worktop oil is based on modified, unsaturated vegetable oils such as linseed oil and tung oil. When exposed to oxygen, the oil molecules cross-link and harden inside the wood to become tough and elastic. The formulation does not contain any biocides active ingredients nor preservatives and is manufactured without cobalt-containing compounds and oximes. The hardened material is harmless to humans, animals and plants. It corresponds to the highest Giscode group Ö10+, DIN EN 71-3 (safety of toys) and DIN 53160 (saliva and sweat fastness) and is LFGB-certified. It can can therefore be processed without hesitation on wooden surfaces that come into contact with food.The applicationPreparation: Carefully sand the wooden surface. Start with coarse sanding, finish with 180-240 grit. The wood moisture should be 8-12%. The surface must be dry, free of grease, thoroughly cleaned and free of grinding dust. material process at room temperature. Tip: If possible, neutralize wood containing tannic acid, such as oak, before oiling. Processing: Rub in the oil with a beige pad by hand or with an eccentric sander until the surface is evenly wetted. Re-oil in dry areas. Wipe off wet oil with a cotton cloth or oil absorbent cloth within 30 minutes and polish out The surface should feel dry. If necessary, polish again the following day with a white polishing pad, cotton or oil absorbent cloth and a little oil (5-10 ml/m²).The surface is dry and brittle? The water resistance and depth of color are decreasing? - Now it should be maintained! In order to maintain the protective effect, it should be re-oiled occasionally. Simply put some worktop oil on a beige pad or a cotton cloth and massage in gently. The following applies to everyday cleaning: Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a slightly damp cotton cloth and then wipe dry. You can remove stubborn dirt Remove gently with our wood soap - diluted with water or undiluted, depending on the degree of soiling. Do not reach for all-purpose or conventional household cleaners, as these can leach out the wood and damage the protection. In order to maintain the protective effect, it should be re-oiled occasionally. Simply put some worktop oil on a beige pad or a cotton cloth and massage in gently. Consumption: 1 application, depending on the absorbency of the wood approx. 20-40 ml/m² per application (approx. 25-50 m²/l).Drying: Depending on the humidity/temperature, the surface is dust-dry after 1-2 hours and fully hardened after 5-7 days. Protect from water during this time and treat gently.NOTE: Cloths/pads soaked with oil can self-ignite due to heat accumulation! Therefore, clean them immediately after use or store them under water. The product itself is of course not self-igniting.

Super pads for random orbital sanders in beigeFor spreading, massaging in & polishing out oils & waxes on natural wood surfacesThe super pads 152 mm in white, beige and green consist of a mixture of polyester and/or nylon fibers, which have been provided with a tough, very elastic acrylic/latex binder and impregnated and coated with abrasive particles (aluminium oxide). The super pads are suitable for sanding discs with a diameter of 125 mm & 150 mm. The pads can be used on both sides with equal effectiveness! This means there is no need to change them frequently.The colors of the pads represent a certain hardness/coarseness and the associated properties. Dimensions: Ø 152 mmContents: 5 pieces, individually packaged in a box Colors - PropertiesSuperpad, white (polishing & massaging pad) Properties: Soft, particularly thick and non-abrasive (abrasive-free) For polishing maintenance oils For polishing & removing oil residues after exposure time For oiling & waxing natural wood surfaces made of softwoodSuperpad, beige (massaging pad - hardwood) Properties: Medium soft, extra thick and non-abrasive For oiling & waxing natural hardwood surfaces Even distribution and deep massaging of the oil and waxSuperpad, green (cleaning pad) Properties: Hard, slightly abrasive For cleaning light to medium soiling Placed wood fibers are cut and the surface is smoothed

OLI-NATURA Scandic Oil - for FurnitureParquet oil in raw wood effectOLI-NATURA Scandic Oil - Classic is inspired by Scandinavian style and combines a natural look with surface protection. It makes light wood look as if untreated and freshly sanded. The natural colour of the wood is almost unfired (highlighted). Only during processing does a colour deepening appear in the wet phase. This, however, disappears in the course of drying.This oil gets its raw wood effect from a VOC-free compound of vegetable oils, which we emulsify in water. Added to this is a fine pinch of light-stable white pigments, which round off the raw wood effect and provide UV protection. Due to its low viscosity, Scandic-Oil Classic is recommended for roller application on light wood floors such as oak, fir, spruce or ash. The dried coating is harmless to humans, animals and plants, complies with DIN EN 71-3 ( Safety of toys) as well as DIN 53160 ( Saliva and perspiration resistant) and is a building product approved by the German Institute for Building Technology (DIBt). Thanks to the intelligent formulation, the oil-soaked rags, pads or brushes do not tend to self-ignite . The applicationPreparation:Sand the wood surface carefully. Start with coarse sanding. Final sanding for furniture surfaces with P240 grit. Wood moisture content: 8-12%. The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature. Application: For the first oil application, apply oil evenly and generously with a short-pile microfibre roller. Work quickly because of the rapid drying and avoid rolling into oil that has already dried. Allow the surface to dry for at least 2-3 hours. Then sand the dried oil application intermediately with grit P220-P280. A P220 sanding sponge is best for this - Dust the surface well. Apply the second oil coat evenly with a microfibre roller and allow to dry. During application, a colour deepening occurs in the wet phase, which disappears after complete drying. The surface is dry and brittle? The water resistance is weakening? - Now it's time for maintenance! The following applies to everyday cleaning: Regular dusting forms the basis. Regular damp care with wood soap ensures quick cleanliness and regreasing. Never use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. The wood can always be refreshed with OLI-Natura Wood Refresher. It renews the protective effect and provides a water-repellent surface without changing the colour tone of the wood. Worn areas on floors or stairs that have been treated with OLI-NATURA Scandic-Oil can be partially sanded and re-oiled without having to re-treat the entire surface.Consumption: With 2 applications and depending on the absorbency of the substrate, approx. 60-80g per m² this corresponds to 12-15 m² per litre. Drying: Depending on humidity and temperature, the surface is: dust-dry after 1 hour, carefully walkable after 2 hours. Protect from water during the first 3-5 days until complete curing.

Sweden red grinding pad 13 inches / Ø 330 mm - grain size 150The Swedish red standard pad with a diameter of 330 mm is specially designed for disc sanders and is ideal for intermediate sanding, cleaning sanding or preparing for a new seal. It offers a particularly fine sanding pattern with a grit size of 150 and impresses with its consistent removal rate. Advantages at a glance:Suitable for initial, intermediate and cleaning sanding Gentle sanding pattern leaves hardly any sanding marks Universally applicable with 13-inch disc machines 8 mm thick robust and durable High-quality craftsmanship Application:The pad is versatile for sanding old sealants, intermediate sanding when re-sealing or for cleaning oiled wood floors. Unlike sanding grids, it works particularly gently and controlled, leaving virtually no scratch marks. One side of the pad is sufficient for approx. 10-15 m² (depending on the surface and pressure) ideal for professional results with minimal effort. Product details:Diameter: 330 mm (13 inches) Thickness: approx. 8 mm Grit: approx. 150 Color: Swedish red Contents: 1 piece Tip: Also ideal for use on parquet, floorboards, or wooden stairsperfectly prepared for subsequent oiling or varnishing.

Care set no. 4 with linseed oil varnishPractical complete set for the initial treatment and care of your wooden chopping boards and kitchen utensilsContents of care set no. 1: 250ml OLI-NATURA linseed oil varnish: Provides deep protection and refreshment 2in1 sanding sponge P220: Enables precise fine sanding for optimum surface preparation Two white pads: Ideal for evenly massaging in the oil Oil absorbent cloth: Removes excess oil and ensures a perfect finish Disposable gloves: Keep your hands clean during care Care flyer: With care tips and a QR code to the application videoThe Care Set No. 4 offers pretty much everything wood cutting board lovers* need, from high-quality OLI-NATURA linseed oil varnish to practical pads. It is ideal for deeply effective protection and care of kitchen boards, snack and chopping boards, kitchen covers and other wooden utensils. Whether as a gift or for yourself - our care set no. 4 is the ideal choice. Application:Basic treatment The cutting board must be clean and dry before you start oiling. If the raw wood surface appears somewhat rough, sand it with the fine sanding sponge P220, applying light pressure along the grain. Then remove the sanding dust. Shake the container and apply a little linseed oil varnish to the surface. You can apply the oil with a brush or the white pad in circular movements. If the wood absorbs more quickly in places and appears dry, simply apply a little more oil. Let the oil soak in for around 15-20 minutes, depending on the size of the surface. Then remove the excess oil with the oil absorbent cloth or kitchen paper until there is no more excess oil and the wood feels dry to the touch. Leave the freshly oiled chopping board to dry overnight. Repeat the process 1-2 times as required to achieve good saturation of the wood.Maintenance treatment The cutting board must be clean and dry before you refresh it Shake the container well before use. Pour some OLI-NATURA Linseed Oil Varnish onto the white pad or a cloth (old, discarded cotton T-shirts are ideal cloths for this purpose) and massage the oil into the wood using circular movements. Let the oil soak in briefly, depending on the size of the surface. Then remove the excess oil with the oil absorbent cloth or kitchen paper until there is no more excess oil and the wood feels dry to the touch. Let the freshly oiled chopping board harden in the air for around 1-2 days before using it again.

OLI-NATURA Colour-OilProtect and colour with just one application.OLI-NATURA Colour-Oils made from linseed oil are based on our OLI-NATURA Worktop-Oil - but combined with colour pigments. It is suitable for the initial and subsequent treatment of wooden furniture and protect & colour with only one application of oil. The different colour shades are ideal for raw and freshly sanded furniture and stairs made of wood, veneer or MDF. The fast-curing colour oils are abrasion-resistant and create a matt, water-repellent & resistant surface. The pigmented "OLI-NATURA Colour-Oil" is available in five colours, all of which are mixable with each other. To achieve a less intense colour result, the Colour-Oil can be mixed with the OLI-NATURA Worktop-Oil..The OLI-NATURA Colour-Oils, rich in solids, are based onmodified, unsaturated vegetable oils such as linseed oil and tung oil as well as lightfast earth/mineral pigments. When exposed to oxygen, the oil molecules cross-link and harden viscoplasticly inside the wood. The colour oils contain neither biocidal agents nor preservatives and are manufactured without cobalt-containing compounds as well as oximes. The cured material is harmless to humans, animals and plants. It complies with the applicable provisions of the German Food, Commodities and Feed Code (LFGB) and Regulation (EC) No. 1935/2004 and can therefore be used without hesitation on wooden surfaces that come into contact with food. It complies with DIN EN 71-3 (Safety of toys) and DIN 53160 (Saliva and sweat fastness). The application:Preparation: Carefully sand the wood surface. Start with coarse sanding, final sanding with grit 180-240. The wood moisture content should be 8-12%. The surface must be dry, free of grease, thoroughly cleaned and free of sanding dust. Apply material at room temperature. Tip: If possible, neutralise woods containing tannic acid, such as oak, before oiling. Application: Massage in oil with beige pad by hand or random orbital sander until surface is evenly wetted. Re-oil in dry areas. Within 30 minutes, remove wet oil with a cotton cloth or oil absorbent cloth and buff out. The surface should feel dry. If necessary, polish again the following day with a white polishing pad, cotton or oil absorbent cloth and a little oil (5-10 ml/m²)..The surface is dry and brittle? The water resistance and colour depth is diminishing? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1 application, depending on the absorbency of the wood approx. 20-40 ml/m² per application (approx. 25-50 m²/l).Drying: Depending on humidity/temperature, the surface is dust-dry after 1-2 hours, fully cured after 5-7 days. During this time, protect from water and handle with care.NOTE: Oil-soaked cloths/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is of course not self-igniting.

Super pads for random orbital sanders in greenFor spreading, massaging in & polishing out oils & waxes on natural wood surfacesThe super pads 152 mm in white, beige and green consist of a mixture of polyester and/or nylon fibers, which have been provided with a tough, very elastic acrylic/latex binder and impregnated and coated with abrasive particles (aluminium oxide). The super pads are suitable for sanding discs with a diameter of 125 mm & 150 mm. The pads can be used on both sides with equal effectiveness! This means there is no need to change them frequently.The colors of the pads represent a certain hardness/coarseness and the associated properties. Dimensions: Ø 152 mmContents: 5 pieces, individually packaged in a box Colors - PropertiesSuperpad, white (polishing & massaging pad) Properties: Soft, particularly thick and non-abrasive (abrasive-free) For polishing maintenance oils For polishing & removing oil residues after exposure time For oiling & waxing natural wood surfaces made of softwoodSuperpad, beige (massaging pad - hardwood) Properties: Medium soft, extra thick and non-abrasive For oiling & waxing natural hardwood surfaces Even distribution and deep massaging of the oil and waxSuperpad, green (cleaning pad) Properties: Hard, slightly abrasive For cleaning light to medium soiling Placed wood fibers are cut and the surface is smoothed

OLI-NATURA High-Solid Hard Wax Oil - colouredProtects with just one application of oil and sets the tone.The pigmented OLI-NATURA HS Hard Wax Oil combines the best properties of natural oils and waxes and protects the wood with just one application. The oils penetrate deep into the wood and protect the wood from the inside. The wax remains on the surface and forms an additional, insensitive and pleasant-to-the-touch protective layer. The high solid content of 100% guarantees maximum resistance and gives the wood even more expression. The surface is easy to maintain and can be re-oiled and repaired again and again. The wood remains breathable and open to diffusion: moisture from the air can be absorbed and released again. This ensures a balanced indoor climate, which has a positive effect on people's well-being.A range of 11 colours is offered, from polar white to various shades of grey to anthracite black, all of which can be mixed with each other. In this way, the user can also create his own colours. Mixing with the natural shade is particularly recommended if you want to achieve a less intense result. The pigments preserve the structural appearance of the wood and give the surface a natural colourfulness. At the same time, the UV-stable colour pigments help to counteract the natural colour change of the wood for as long as possible.The "OLI-NATURA HS Hard Wax Oil" is cobalt- and oxime-free and suitable forchildren's toys. The cured material is saliva and perspiration resistant and thus harmless for humans, animals and plants as well as a building product approved by the German Institute for Building Technology (DIBt).Suitable for: For untreated, freshly sanded or leached solid wood indoors. Particularly suitable for floorboards, parquet and wooden floors.ApplicationPreparation:Sand wood surface carefully, start with coarse sanding, final sanding for floors P100-150, for furniture P180-240. wood moisture: 8-12%. The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/agitate well.In the parquet area: Apply oil evenly thinly in sections for 5-10 m² with microfibre roller, oil applicator, oil brush or flat brush. After 30-60 minutes, massage in with a single-disc machine and beige pad until the wood is saturated and appears evenly matt. For final polish and to remove any excess oil, buff out with a polishing pad/oil absorbent cloth. In furniture: Apply an even thin coat of oil with a flat brush/surface brush in the direction of the grain. After 30 minutes exposure time in the wet phase, massage in with beige pad until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. Alternatively, the oil can also be sanded into the wood with a soaked, fine sanding fleece. After a short reaction time, remove any excess oil with a cotton cloth/oil absorbent cloth. The surface should appear evenly matt. The surface is dry and brittle? The water resistance and colour depth is diminishing? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1 coat, depending on the absorbency of the substrate 20-40 g/m² per coat (25-50 m²/l) .Drying: Depending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully cured after 2-3 days - as 2-component version after 24 hours. Protect from water during this time. Consumption/drying depend on the type of wood and the absorbency of the substrate. Excess material on non-absorbent areas delays drying, as do low temperatures and/or excessive humidity and/or excessive wood moisture. Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA Yacht & Teak OilWeather-resistant hardwood oil with UV protection.The hardwood oil OLI-NATURA Yacht & Teak Oil in natural and teak protects the wood against sun, rain and greying. Equipped with UV protection, it gives garden furniture, terraces, pool surrounds and yacht decks made of hardwood and exotic wood as well as pressure-treated softwood a weather-resistant surface. The naturally drying oil based on natural oil does not form a surface film, but rather represents an open-pored impregnation. It does not crack, flake or peel, but penetrates deeply into the wood and fills the capillaries. This ensures very good water resistance. The wood remains permeable to diffusion and can release absorbed atmospheric moisture again.With the colourless version Nature, the grain and colour of the wood are particularly beautifully emphasised. The lightly pigmented version Teak brings transparent colour to the wood. The pigments preserve the structure of the wood and give the surface a natural colour. At the same time, the UV-stable colour pigments help to counteract the natural colour change of the wood for as long as possible. The oils are free of biocidal agents and can therefore also be used for wood indoors.The applicationPreparation: The wood must be clean, dry and free of grease. If the wood is very dirty, it is advisable to clean it first. If necessary, smooth out protruding wood fibres and rough areas with fine sandpaper (220 grain). Shake/stir the container well before use.Application: Spread the oil evenly in a thin layer with a brush, flat brush or roller in the direction of the grain. After 20-30 minutes of exposure time in the wet phase, repolish with a white pad or cotton cloth. Remove any excess oil with an oil absorbent cloth or similar. If the wood is very dry, repeat the application as described above. Info: Do not paint exterior wood in damp weather or in full sun. The surface is dry and brittle? The water resistance and colour depth is weakening? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1-2 applications | Depending on the absorbency of the substrate 40-80 g/m² per application (12-25 m²/l).Drying: Depending on the weather, dust-dry after 1-2 hours and fully cured after 2-3 days. Protect from water during this time. Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA Project OilDeep-acting universal oil.OLI-NATURA Project Oil, based on natural oils, is used for the treatment of furniture, stairs and floorboards on almost all types of wood. It gives the wood a colour-deepening appearance and the grain emerges wonderfully. It has a solid content of 60 %, penetrates deep into the pores and protects the wood reliably from the inside. The deep penetration of the oil produces a clearly darker colour, the so-called permanent wet effect. It does not form a surface layer, but rather represents an open-pore impregnation. Thanks to the high self-penetration of the project oil, it is particularly easy to apply and very economical. With only one to two applications, extremely water- and dirt-repellent wood surfaces are achieved that are easy to maintain and repair-friendly. The project oil is ideal for all leached, untreated, sanded or new wood surfaces, but also for coarse chipboard (OSB) and cork in interior areas.The cured material is harmless to humans, animals and plants. It complies with DIN EN 71-3 (Safety of toys) as well as DIN 53160 (Saliva and perspiration fastness) and is a building product approved by the German Institute for Building Technology (DIBt).The applicationPreparation:Sand wood surface carefully, start with coarse sanding, final sanding for furniture P180-240, for floors P100-150. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well!In furniture: Apply oil thinly and evenly in the direction of the grain with a flat brush/surface brush. After 20-30 minutes exposure time in the wet phase, massage in with a pad (white or beige) or buff out with a cotton cloth/oil absorbent cloth until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. If necessary, a second coat can be applied as described above after drying overnight. In the parquet area: Apply oil evenly thinly in sections for 5-10 m² with an oil roller, oil applicator, oil brush or flat brush. After 20-30 minutes exposure time in the wet phase, massage in with white or beige pad by hand or single-disc machine until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. After drying overnight, apply a second coat as described above..The surface is dry and brittle? The water resistance and colour depth is decreasing? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1-2 applications | Depending on the absorbency of the substrate, approx. 40-50 g/m² per application (20-25 m²/l).Drying: Depending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully cured after 2-3 days. Protect from water during this time.Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-Natura HS Hardener - B-ComponentThis hardener component can optionally be added immediately before processing the following oils from OLI-Natura: HS Hard Wax Oils, HS Professional Oils, Worktop-Oil and Colour-Oil.. In addition to the pure oxidative drying, the OLI-NATURA HS Hardener also initiates a cross-linking reaction of the oil molecules. This results in the formation of particularly close-meshed oil structures that are firmly anchored in the wood and highly resistant. Surfaces treated in this way can be loaded earlier with only one application, have a greater final hardness and a higher abrasion resistance. The addition depends on the oil in question.Application / processing instructions. Optimum processing conditions at 20°C and 50% relative humidity. Do not process below +15 °C Mix hardener thoroughly in the specified mixing ratio just before use. Process the mixture immediately. The dripping time is 2-3 hours for colourless oils (natural) and 1-2 hours for coloured oils. Do not pour back excess material. Danger of spontaneous combustion! Clean soaked rags/pads immediately after use or store under water. Oxidative drying. Provide open windows during and after processing to achieve air circulation. Mixing ratios:HS Hard Wax Oil - 1 part hardener to 10 parts oil (1:10). HS-Profiöl - 1 part hardener to 10 parts oil (1:10) Worktop-Oil - 1 part hardener to 5 parts oil (1:5) Colour-Oil - 1 part hardener to 5 parts oil (1:5)

Care Set No. 3 with RefresherPractical complete setContents of Care Set No. 2: 250 ml OLI-NATURA Wood Soap250 ml OLI NATURA Refresher1 care flyer with step-by-step instructions and tips1 polishing pad1 oil absorbent clothThe practical care set is suitablefor perfect maintenance. set is perfect for the cleaning and care of Scandic-Oil oiled and white & natural oiled wooden surfaces. With the concentrated "OLI-NATURA Wood Soap", dirt can be gently removed without damaging the wood. Intensive color refreshment and care of the wood in depth can be achieved with the "OLI-NATURA wood care oil". The special POLISHING PAD is used to massage in the care oil and the OIL WIPER is used to remove standing oil and for final polishing. The ONE-TIME GLOVES keep your hands clean. We have also included extensive instructions with lots of tips.Particularly resource-conscious people will be pleased to know that the care oil should only ever be applied sparingly. The 250 ml tin can be used to care for and maintain a whole lot of beautiful natural oiled furniture.Application: For refreshing and maintaining Scandic-Oil oiled and white & natural oiled wooden surfaces.

OLI-NATURA High-Solid Hard Wax OilProtects with just one application of oil.The solvent-free OLI-NATURA HS Hard Wax Oil combines the best properties of natural oils and waxes and protects the wood with only one application. The oils penetrate deep into the wood and protect the wood from the inside. The wax remains on the surface and forms an additional, insensitive and pleasant-to-the-touch protective layer. The high solid content of 100% guarantees maximum resistance and gives the wood even more expression. The surface is easy to maintain and can be re-oiled and repaired again and again. The wood remains breathable and open to diffusion: moisture from the air can be absorbed and released again. This ensures a balanced room climate, which has a positive effect on people's well-being.The "OLI-NATURA HS Hard Wax Oil" is based on modified vegetable oils and waxes. It offers the highest Giscode rating Ö10+, because it is formulated without solvents and free of biocides,cobalt-containing compounds as well as oximes. That is why our "OLI-NATURA HS Hard Wax Oil" is so healthy for the home and suitable for children's toys. It is also LFGB-certified (food safe). The cured material is saliva- and perspiration-proof and thus harmless to humans, animals and plants as well as a building product approved by the German Institute for Building Technology (DIBt).Suitable for: For untreated, freshly sanded or leached solid wood indoors. Particularly suitable for floorboards, parquet and wooden floors.ApplicationPreparation:Sand wood surface carefully, start with coarse sanding, final sanding for floors P100-150, for furniture P180-240. wood moisture: 8-12%. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/agitate well.In the parquet area: Apply oil evenly thinly in sections for 5-10 m² with microfibre roller, oil applicator, oil brush or flat brush. After 30-60 minutes, massage in with a single-disc machine and beige pad until the wood is saturated and appears evenly matt. For final polish and to remove any excess oil, buff out with a polishing pad/oil absorbent cloth. In furniture: Apply an even thin coat of oil with a flat brush/surface brush in the direction of the grain. After 30 minutes exposure time in the wet phase, massage in with beige pad until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. Alternatively, the oil can also be sanded into the wood with a soaked, fine sanding fleece. After a short reaction time, remove any excess oil with a cotton cloth/oil absorbent cloth. The surface should appear evenly matt. The surface is dry and brittle? The water resistance and colour depth is diminishing? - Now it's time for maintenance!In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1 coat, depending on the absorbency of the substrate 20-40 g/m² per coat (25-50 m²/l) .Drying: Depending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully cured after 2-3 days - as 2-component version after 24 hours. Protect from water during this time. Consumption/drying depend on the type of wood and the absorbency of the substrate. Excess material on non-absorbent areas delays drying, as do low temperatures and/or excessive humidity and/or excessive wood moisture. Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA furniture wax - in a 125ml canColorless furniture wax with natural beeswax and carnauba waxOLI-NATURA furniture wax nourishes the wood and creates a velvety feel, as well as a patina that deepens over time. It not only makes the surface water-repellent, but also prevents dirt from penetrating the wood. Really old or trimmed to look antique, whether untreated or open-pore oiled or waxed, whether stained or painted with chalk paint: »OLI-NATURA furniture wax« is suitable for all types of wood. The wax has a pleasant subtle scent.OLI-NATURA furniture wax is made from 100% real beeswax and carnauba wax and other proven raw materials using traditional methods. On the use of fragrances (terpenes), preservatives, formaldehydes, aromatics and cobalt salts are deliberately avoided. The wax is VOC-free and complies with DIN EN 71-3 (safety of toys) and DIN 53160 (saliva and sweat fastness) The applicationThe preparation: Before you get started, the piece of furniture must be clean and free of dust and grease. If this is an initial treatment, it is advisable to finely sand the surface beforehand using 180 to 240 grit. When caring for furniture or post-treatment, grinding is not necessary. Processing: Always impregnate in a warm room. This makes the wax softer and smoother and easier to work with. Apply the wax evenly and in small circular motions with a soft, lint-free cloth cloth or roll of cloth. Do not use too much or too little wax. Depending on how well the pores of the wood are open, the wax will soak in more quickly or more slowly. Be patient and allow the wax to dry thoroughly. Finally polish the surface thoroughly with a soft cloth. You can achieve a special shine with a white polishing pad. It is better to opt for several thin applications and let the wax dry well in between. This is how the result will be way better.The surface is dry and dull? Is the water resistance declining? - Now it should be cared for!So that the waxed piece of furniture does not lose its charm, it must be cared for and cleaned regularly. dust and adhering dirt can be easily wiped away with a dry or slightly damp, but never wet, cloth. The surface should be waxed from time to time. How regularly the wooden surface has to be maintained depends on various factors from: What kind of wood is the piece of furniture made of? How often is it used? What hardships will it be subjected to?Drying: The final strength is only reached after a few days. During this time, please do not clean with a damp cloth.

Care set no. 1 with natural care oilPractical complete setContents of care set no. 1: 250 ml OLI-NATURA wood soap250 ml OLI-NATURA wood care oil1 care flyer with step-by-step instructions and tips1 polishing pad1 oil absorbent cloth1 disposable gloves (PLA- biodegradable)The practical care set is perfect for the cleaning and care of naturally oiled wooden furniture. With the concentrated "OLI-NATURA Wood Soap", dirt can be gently removed without damaging the wood. Intensive color refreshment and care of the wood in depth can be achieved with the "OLI-NATURA wood care oil". The special POLISHING PAD is used to massage in the care oil and the OIL WIPER is used to remove standing oil and for final polishing. The ONE-TIME GLOVES keep your hands clean. We have also included extensive instructions with lots of tips.Particularly resource-conscious people will be pleased to know that the care oil should only ever be applied sparingly. The 250 ml tin can be used to care for and maintain a whole lot of beautiful natural oiled furniture.Application: For refreshing natural oiled wooden surfaces. If in doubt, apply a sample to a concealed area.Important: Rags/pads soaked with oil can self-ignite due to heat build-up. Therefore, clean them immediately after use or store them under water.

OLI-NATURA High Solid Professional Oil - colouredProtects wood furniture surfaces at the highest level and sets the tone.The OLI-NATURA HS Profi Oil based on natural oils is particularly well suited for floorboards, parquet and wooden floors. The low-solvent OLI-NATURA HS Profi Oil protects wooden surfaces at the highest level. Thanks to the high solid content of 100%it is highly productive and creates an extremely durable, dirt and water-repellent natural oil surface with its matt look and natural feel, which is not only at the feet of barefoot lovers. The OLI-Natura HS professional oil is available in 11 different colours, which can also be mixed with each other. The coloured OLI-Natura HS professional oils are based on modified vegetable oils such as linseed oil and wood oil. The breathable surface can absorb moisture in the room and also release it again. This ensures a healthy living environment. The oil is free of oximes and cobalt and suitable for children's toys. The cured material is saliva- and perspiration-proof and thus harmless to humans, animals and plants as well as a building product approved by the German Institute for Building Technology (DIBt).The applicationPreparation: Sand wood surface carefully, start with coarse sanding, final sanding for furniture P180-240, for floors P100-150. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well!In furniture: Apply a thin, even coat of oil with a flat brush/surface brush in the direction of the grain. After 30 minutes exposure time in the wet phase, massage in with beige pad until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. Alternatively, the oil can also be sanded into the wood with a soaked, fine sanding fleece. After a short reaction time, remove any excess oil with a cotton cloth/oil absorbent cloth. The surface should appear evenly matt. In the parquet area: Apply oil evenly thinly in sections for 5-10 m² with a microfibre roller, oil applicator, oil brush or flat brush. After 30-60 minutes, massage in with a single-disc machine and beige pad until the wood is saturated and appears evenly matt. For final polish and to remove any excess oil, buff out with a polishing pad/oil absorbent cloth.The surface is dry and brittle? The water resistance and colour depth is diminishing? - Now it's time for maintenance! In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning: Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1-2 applications | Depending on the absorbency of the substrate, approx. 40-50 g/m² per application (20-25 m²/l).Drying: Depending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully cured after 2-3 days. Protect from water during this time.Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

Care set no. 2 with wood care waxPractical complete setContents of care set no. 2: 250 ml OLI-NATURA wood soap250 ml OLI-NATURA wood care wax1 care flyer with step-by-step instructions and tips1 polishing pad1 oil absorbent cloth1 disposable gloves (PLA- biodegradable)The practical care set is perfect for the cleaning and care of oiled/waxed wooden furniture indoors. With the concentrated "OLI-NATURA Wood Soap", dirt can be gently removed without damaging the wood. Intensive color refreshment and care of the wood in depth can be achieved with the "OLI-NATURA wood care oil". The special POLISHING PAD is used to massage in the care oil and the OIL WIPER is used to remove standing oil and for final polishing. The ONE-TIME GLOVES keep your hands clean. We have also included extensive instructions with lots of tips.Particularly resource-conscious people will be pleased to know that the care oil should only ever be applied sparingly. The 250 ml tin can be used to care for and maintain a whole lot of beautiful natural oiled furniture.Application: For refreshing oiled and hard wax oil-treated wooden surfaces. If in doubt, apply a sample to a concealed area.Important: Rags/pads soaked with oil can self-ignite due to heat build-up. Therefore, clean them immediately after use or store them under water.

OLI-NATURA High Solid Professional OilProtects wood furniture surfaces at the highest level.The OLI-NATURA HS Profi Oil based on natural oils is particularly well suited for floorboards, parquet and wooden floors. The solvent-free OLI-NATURA HS Profi Oil protects wooden surfaces at the highest level. Thanks to the high solid content of 100%it is highly productive and creates an extremely durable, dirt and water-repellent natural oil surface with its matt look and natural feel, which is not only at the feet of barefoot lovers. The OLI-NATURA HS Professional Oil is based on modified vegetable oils such as linseed oil and wood oil. It offers the highest Giscode rating Ö10+ because it is formulated without solvents and is free of oximes and cobalt. That is why our OLI-NATURA HS Profiöl is so healthy for the home and suitable for children's toys. At the same time, the cured material is saliva- and perspiration-proof and thus harmless tohumans, animals and plantsas well as a building product approved by the German Institute for Building Technology (DIBt).The applicationPreparation:Sand wood surface carefully, start with coarse sanding, final sanding for furniture P180-240, for floors P100-150. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well!In the furniture area: Apply oil thinly and evenly in the direction of the grain with a flat brush/surface brush. After 30 minutes exposure time in the wet phase, massage in with beige pad until the surface appears evenly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. Alternatively, the oil can also be sanded into the wood with a soaked, fine sanding fleece. After a short reaction time, remove any excess oil with a cotton cloth/oil absorbent cloth. The surface should appear evenly matt. In the parquet area: Apply oil evenly thinly in sections for 5-10 m² with a microfibre roller, oil applicator, oil brush or flat brush. After 30-60 minutes, massage in with a single-disc machine and beige pad until the wood is saturated and appears evenly matt. For final polish and to remove any excess oil, buff out with a polishing pad/oil absorbent cloth.The surface is dry and brittle? The water resistance and colour depth is diminishing? - Now it's time for maintenance! In order to maintain the protective effect, oiling should be done occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.The following applies to everyday cleaning: Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be removed gently with our wood soap - diluted with water or pure, depending on the degree of soiling. Do not use all-purpose or conventional household cleaners, as these can leach out the wood and attack the protection. To maintain the protective effect, oil the wood occasionally. To do this, simply apply a little oil to a beige pad or cotton cloth and massage in gently. Consumption: 1-2 applications | Depending on the absorbency of the substrate, approx. 40-50 g/m² per application (20-25 m²/l).Drying: Depending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully cured after 2-3 days. Protect from water during this time.Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

Nordic B - ultra-matt colored paint2in1 colored paint based on bio-acrylateNORDIC B, the ultra-matt colored paint in Pigeon Blue based on aqueous bio-acrylates for furniture, doors & kitchen fronts, stair coverings or skirting boards. The trend-conscious colors for indoor use are easy to paint, roll & spray and are ideal for wood, melamine resin boards, MDF and plywood. Also suitable for children's furniture & toys.The ultra-matt finish combines the natural look of a chalk paint with the durability of a varnish. Because Nordic B is basecoat & topcoat in one product and therefore saves you time and money.The 15 ultra-matt shades are highly opaque - with just two coats of paint. The NORDIC B colored paints come with an amazing gloss level of less than 5 gloss. The matt paint finish diffuses the light, further enhancing the dull matt effect. The soft-touch matt surface with anti-fingerprint effect literally invites you to touch it: whether powder-matt kitchen fronts in country house style or children's furniture in hygge colors: The paint series creates a feel-good atmosphere in your home.Environmentally friendly & mild-smelling: With the NORDIC B colored paints comes a new generation of colored water-based paints in premium quality, which are characterized by sustainability and high performance. They contain the highest proportion of biogenic raw materials, which are made from plant alcohol esters from pine and castor bean. In addition, only mineral color pigments are used, which are characterized by high lightfastness and UV stability. The environmentally friendly water-based paint also complies with the EU Decopaint Directive, is harmless to humans, animals and plants and complies with DIN EN 71-3 (safety of children's toys) and DIN 53160 (saliva and sweat fastness). Environmentally friendly - high-solids water-based colored paint based on organic acrylateUltra matt - dries dull matt, gloss level below 5% 2in1 - primer and colored top coat in oneIn 15 harmonious shades - highly opaqueInterior - for furniture, doors, stairs - for wood & wood-based materials, plywood, melamine, MDFEasy to use - can be easily painted, rolled, sprayedHealthy living - suitable for children's toysProcessing and careSurface preparation: Sand the wood surface professionally. Final wood sanding for furniture P150-180. Wood moisture content 8-12 %. The substrate must be firm, dry, clean, non-slip, load-bearing and free of release agents. Apply the material at room temperature. Sand down non-load-bearing, e.g. flaking old coats and grayed wood down to the load-bearing substrate.For higher loads, optionally process with B-component OLI-NATURA Hardener 13.5. Carefully mix the two components A and B in a ratio of 20 to 1. NORDIC 2K can be processed for a maximum of 3 hours after mixing. Processing raw woodShake/stir the container well.Spread, roll (foam roller) or spray the lacquer evenly in the direction of the grain. After approx. 2 hours of drying, sand in the grain direction with P220-P280 grit. Dust off the surface well.Spray, roll (foam roller) or spray a second coat of paint evenly in the direction of the grain.CareWipe with a damp cloth (possibly with a mild detergent).Wipe with a dry cloth.

OLI-NATURA Antique Reactive Stain - Lye-Treated 250 mlThe Antique Lye-Treated Reactive Stain gives tannin-rich woods such as oak a warm, natural aging effect with soft, light tones. The stain reacts with the tannic acid content of the oak and produces an authentic patina, ideal for classic and Scandinavian interior designs.Apply undiluted with a brush, roller or spray gun. After drying, the surface is oiled or waxed. The stain is VOC-free, water-based and particularly suitable for textured surfaces.Advantages at a glance:Naturally leached look with a light aging effect Environmentally friendly & VOC-free Ready to use undiluted application Ideal for raw oak wood Requires follow-up treatment with oil or waxNote: After complete drying (6-8 hours), we recommend a fine intermediate sanding before surface treatment.

OLI-NATURA Hard Wax Oil - COTTON WhiteThe pigmented oil-wax combination in the color COTTON White.The OLI-NATURA Hard Wax Oil is a pigmented hard wax oil with 60% solid content for the treatment of wood indoors and combines the best properties of wax and oil. While the oil penetrates the wood and protects it from the inside, the wax forms a robust and water-repellent surface film. The wood remains open-pored, can continue to breathe and thus positively influences the indoor climate. Seven colors are offered, from SAFRAN RED to COTTON WHITE to PEPPER BLACK, all of which can be mixed with each other. In this way, the processor can also create colors himself. A second application intensifies the color effect. To tone down the color, the "OLI-NATURA COLOUR Hard Wax Oil" can also be mixed with the colorless "OLI-NATURA Hard Wax Oil". The "OLI-NATURA Hard Wax Oil" consists of modified vegetable oils, such as the soybean oil, and waxes, such as the refined carnauba wax, dearomatized hydrocarbon as well as lead- and cobalt-free drying agents. In doing so, we deliberately avoid the use of critical substances such as preservatives, formaldehydes, aromatics, biocides, cobalt salts and oximes.It is "Allergy Friendly Quality Tested" and has been awarded the ECARF seal. It is also LFGB certified (food safe) and complies with Regulation (EC) No. 1935/2004. The cured material is harmless to humans, animals and plants. It complies with DIN EN 71-3 (Safety of toys) and DIN 53160 (Saliva and perspiration fastness) and is a building product approved by the German Institute for Building Technology (DIBt).The application.The preparation: Sand wood surface carefully, start with coarse sanding, final sanding for furniture P180-240, for floors P100-150.Wood moisture: 8-12%. The surface must be dry, thoroughly cleaned and free from oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well. For floors: Apply oil with microfiber roller, oil brush or surface brush in an even thin layer. Work in sections between 5 to 15 m². Leave to act for approximately 30-45 minutes. Now massage in with white pad by hand or polishing machine and remove excess oil with a cotton cloth or oil absorbent cloth. The surface should be dry to the touch and not sticky to the touch. After 24 hours, apply second coat without intermediate sanding.In furniture and staircase areas:Apply oil in an even thin layer with a brush or surface brush in the direction of the grain. Approximately 10-30 minutes allow to act. Now remove excess oil with a cotton cloth or oil absorbent cloth. The surface should now be dry to the touch and not feel sticky. For large surfaces, use white pad if necessary. If necessary, a second coat can be applied after 24 hours without intermediate sanding.Tip:A second application intensifies the intensity of the color.For small components or surfaces, a better result can be achieved by applying the hard wax oil directly with a soaked cotton cloth and wiping.For heavily used surfaces, it is recommended to apply a second coat after 24 hours at the earliest..The surface is dry and brittle? The water resistance and color depth is weakening? - Now should be maintained!To maintain the protective effect, should be occasionally re-oiled. To do this, simply apply a little oil to a beige pad or cotton cloth and gently massage it in.For everyday cleaning applies:Regular dusting forms the basis. For light soiling, it is usually sufficient to wipe the surface with a damp cotton cloth and then wipe dry. Stubborn dirt can be gently removed with our wood soap - diluted with water or pure, depending on the degree of soiling. Do never reach for all-purpose or conventional household cleaners, because these can leach out the wood and attack the protection. To maintain the protective effect, you should occasionally re-oil. To do this, simply apply some oil to a beige pad or cotton cloth and massage gently. Consumption: 1-2 applications I Depending on the absorbency of the wood 40-50 g/m² per application (20-25 m²/l).Drying: Depending on humidity/temperature, the surface is dust-dry after 1-2 hours, fully cured after 2-3 days. Protect from water during this time.Note: Oil-soaked rags/pads can self-ignite due to heat build-up! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.

OLI-NATURA MAINTENANCE SET No. 1Care set for lacquered surfacesWell cared for simply lasts longer: That is exactly why we present the MAINTENANCE SET #x2116; 1 for the cleaning and care of lacquered wood surfaces. This set includes optimally coordinated products, so you save time and effort in searching and combining individual items. WOOD SOAP: 250 ml wood soapWOOD BALM: 250 ml wood care balmCOTTON-CLOTH: 45x45 cm jersey cotton clothMAINTENANCE-FLYER: Includes care tips and QR code to application videoApplicationApplication "WOOD SOAP":First remove loose dirt by dusting. Shake the bottle well before use.As needed, add about 5-10 ml (2-4 tsp) of wood soap to 1 liter of lukewarm water and mix well. Wipe the surface with a wrung-out cloth until damp.Finish by wiping with a dry cloth.Application "WOOD BALM":First remove loose dirt by dusting. For stubborn dirt, damp clean and then allow the surface to dry thoroughly.Shake the bottle well before use.Follow with a small amount in a lint-free cloth (such as cotton) and apply evenly in the direction of the grain of the surface. Allow the balm to soak in and wipe down if necessary. Do not leave puddles.After 1-2 hours, the surface is usable with care. Full usability is achieved after about 12 hours.Notes & Tips:To clean the painted furniture, it is best to use a lint-free, soft cotton cloth. Old, discarded cotton t-shirts also work well. Please refrain from using microfiber cloths or rough sponges, as they can cause scratches on the surface.Please do not use aggressive, strongly alkaline or solvent-based cleaning or scouring agents, as such products can damage the lacquer surface.Avoid standing moisture, e.g. from wet glasses, leaking flower pots or vases. Spills should be wiped away immediately.Avoid standing moisture, e.g. from wet glasses, leaking flower pots or vases. Spills should be wiped away immediately.Do not place hot pots or the like on lacquered furniture as they may cause stains..

OLI-NATURA Project Oil coloredDeep-acting universal oilThe OLI NATURA Project Oil in the color "Lime white" is a deep-acting impregnation oil on natural oil basis with 60% solid content. As a result, it is absorbed deep into the pores and protects the wood reliably from inside. The project oil does not form a surface layer, but rather represents an open-pore impregnation. Thanks to the high self-penetration of the project oil, it is particularly easy to process and very economical. With only one or two applications, extremely water and dirt-repellent wood surfaces are achieved that are easy to maintain and friendly to repair.There are four colors that preserve the natural charm of the wood and haptically enhance the surface. The pigments preserve the textured appearance of the wood and give the surface a natural color. At the same time, the UV-stable color pigments help to counteract the natural color change of the wood for as long as possible.The easy-to-apply project oil is ideal for all leached, untreated, sanded or new wood surfaces, but also for coarse chipboard (OSB) and cork in the interior: whether for wood or frame furniture, wall paneling, doors or kitchen furniture, parquet flooring or stairs. ApplicationDepending on the area of application, the material is applied in one or two operations with a brush, a pad, an oil roller, so that the entire wood surface is glossily wetted. After a short exposure time, the excess is simply removed with a cotton cloth/oil absorbent cloth and polished off again. If necessary, after drying overnight, a second application can be made without intermediate sanding.For furniture subject to normal wear, a single application is usually quite sufficient. Floors, stairs or highly stressed furniture, however, require more protection. Here, a second application is recommended.PreparationSand the wood surface carefully, starting with coarse sanding, final sanding for furniture P180-240, for floors P100-150.The surface must be dry, thoroughly cleaned and free of oil, wax, grease, silicone and sanding dust. Apply material at room temperature and shake/stir well!In furnitureApply oil thinly and evenly with flat brush/surface brush in grain direction. Allow to react for 20-30 minutes. Expel with lint-free cotton cloth/oil absorbent cloth and buff until surface appears dry. For large areas, use beige pad if necessary. If necessary, a second application can be made after 6-8 hours without intermediate sanding.In the parquet areaApply oil evenly thinly in sections for 5-10 m² with mohair roller, oil applicator, oil brush or surface brush. After 20-30 minutes exposure time in the wet phase, massage in with white or beige pad by hand or single-disc machine until the surface appears uniformly matt. Remove any excess oil with a cotton cloth/oil absorbent cloth. After drying overnight, apply a second coat as described above.Care and cleaning:Only a few care measures are required to keep the surface in permanently beautiful condition. Dust deposits, for example, are simply wiped off with a dry, possibly damp cloth.Parquet floors, on the other hand, should be vacuumed or swept daily, as sand and dust can cause fine scratches. Adhering dirt can be removed quickly with a mild wood soap. It is important to avoid over-moisture and stagnant moisture.To maintain the protective effect, should be occasionally re-oiled. To do this, simply apply a little oil to a beige pad or cotton cloth and massage gently. For normal maintenance cleaning, we recommend OLI-NATURA wood soap. This way the pores of the wood are filled up with oil again and the protective effect is renewed. After such treatment, the wood is antistatic and therefore attracts less dust.In addition, the oiled surface can be easily reworked, which is not possible with lacquered surfaces. The affected area can be easily sanded in places and retreated without having to renovate the entire surface.Consumption1-2 applications | Depending on the absorbency of the substrate about 40-50 g/m² per application (20-25 m²/l).DryingDepending on humidity and temperature, the surface is dust-dry after 1-2 hours and fully hardened after 2-3 days. During this time, protect from water.The consumption / drying depends on the type of wood and the absorbency of the substrate. Excess material on non-absorbent areas delays drying, as do low temperatures and / or excessive humidity and / or excessive wood moisture.NOTE ON SELF-INFLAMATION HAZARD:Oil-soaked rags / pads can ignite themselves due to heat accumulation! Therefore, clean them immediately after use or store them under water. The product itself is not self-igniting.