DilaTec expansion joint base profile 5 x 25 mm - aluminium - for coverings up to 6mm - 2.50m . Important! This is only a base profile from the DilaTec expansion joint system! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The separately available plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 1 base profiles made of aluminium. Plastic expansion joint strips available separately Suitable for coverings up to 6mm Length: 2,500 mm Height x width: 5 x 25 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Beige 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Beige 2,50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - light grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Beige 2,50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - light grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 4-6mm coverings Length: 2,500 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Black 2,50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 4-6mm coverings Length: 2,500 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Black 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Dark grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 4-6mm coverings Length: 2,500 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - light grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Beige 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - light grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Dark grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Dark grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Beige 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Black 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Black 2,50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - light grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Dark grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Beige 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 base profiles each 25mm wide made of aluminium. 1 plastic expansion joint strip. Joint colour: beige Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 54 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Black 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Black 2,50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - light grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Dark grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 2-4mm coverings Length: 3,000 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 2-4mm coverings - Dark grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 2-4mm coverings Length: 2,500 mm Height x width: 5 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - light grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - light grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: light grey Suitable for 4-6mm coverings Length: 2,500 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Dark grey 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Dark grey 2.50m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: dark grey Suitable for 4-6mm coverings Length: 2,500 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint system - with 2 base profiles and a plastic expansion joint strip - for 4-6mm coverings - Black 3m. The pre-assembled expansion joint profiles are ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They reliably absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 2 basic profiles, each 45mm wide, made of aluminium. 1 plastic expansion joint strip. Joint colour: black Suitable for 4-6mm coverings Length: 3,000 mm Height x width: 7 x 94 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion joint base profile 5 x 25 mm - aluminium - for coverings up to 6mm - 3m. Important! This is only a base profile from the DilaTec expansion joint system! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The separately available plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 1 base profiles made of aluminium. Plastic expansion joint strips available separately Suitable for coverings up to 6mm Length: 3,000 mm Height x width: 5 x 25 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint base profile 5 x 45 mm - aluminium - for coverings up to 6mm - 3m. Important! This is only a base profile from the DilaTec expansion joint system! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The separately available plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 1 base profiles made of aluminium. Plastic expansion joint strips available separately Suitable for coverings up to 6mm Length: 3,000 mm Height x width: 5 x 45 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec expansion joint base profile 5 x 45 mm - aluminium - for coverings up to 6mm - 2.50m . Important! This is only a base profile from the DilaTec expansion joint system! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The separately available plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without tearing or to separate from the profile. The data at a glance 1 base profiles made of aluminium. Plastic expansion joint strips available separately Suitable for coverings up to 6mm Length: 2,500 mm Height x width: 5 x 45 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Light Grey 3m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: light grey Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 3,000 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Light Grey 2.50m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: light grey Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 2,500 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Light Grey 3m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated for. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: light grey Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 3,000 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Light Grey 2.50m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: light grey Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 2,500 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Dark Grey 3m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 plastic expansion joint strip. Colour: dark grey Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 3,000 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Dark Grey 2.50m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 plastic expansion joint strip. Colour: dark grey Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 2,500 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Beige 3m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: Beige Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 3,000 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Beige 2.50m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: Beige Aluminium base profile is available separately. Suitable for 2-4mm decking Length: 2,500 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Black 3m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated for. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: black Aluminium base profile is available separately Suitable for 2-4mm decking Length: 3,000 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 10mm - Black 2.50m - for 2-4mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: black Aluminium base profile is available separately Suitable for 2-4mm decking Length: 2,500 mm Height x width: 4 x 10 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Dark Grey 3m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated for. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 plastic expansion joint strip. Colour: dark grey Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 3,000 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Dark Grey 2.50m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 plastic expansion joint strip. Colour: dark grey Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 2,500 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Beige 3m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: Beige Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 3,000 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Beige 2.50m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: Beige Aluminium base profile is available separately. Suitable for 4-6mm decking Length: 2,500 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings

DilaTec Expansion Joint Strip 12.6mm - Black 3m - for 4-6mm flooring . Important! This is only the plastic expansion joint strip! The DilaTec expansion joint system is ideal for use on screed joints or wherever tension in the floor needs to be compensated for. The plastic expansion joint strips can be easily replaced. Due to the co-extrusion of hard and soft PVC, they have optimal expansion behaviour. They safely absorb stresses from the substrate - without cracking or to separate from the profile. The data at a glance 1 expansion joint strip made of plastic. Colour: black Aluminium base profile is sold separately Suitable for 4-6mm rubbers Length: 3,000 mm Height x width: 6 x 12.6 mm Suitable for: Design flooring / LVT Dryback, Textile and resilient floor coverings. Application: The expansion joint profile is used for all floor coverings to bridge expansion and construction movement joints. The profile is laid out so that it lies exactly over the joint in the subfloor so that the floor joint can continue to move.. Assembly: Bonding: . Use a two-component or cast resin adhesive or an adhesive with particularly high adhesive strength. After gluing the profile, pull off excess adhesive smoothly. Please follow the manufacturer's instructions. Make absolutely sure that no adhesive penetrates into the floor joint. Filling in: You can also fill in the profile using suitable filling compounds. Note always select the profile so that the height of the profile corresponds to the floor covering plus the filler. Once the adhesive has hardened, the floor covering can be cut to fit the profile. We recommend using this profile only in conjunction with glued floor coverings